Loading... Please wait...

Help Getting Started

EGO SATURN STARTER KIT TUTORIAL

About Your Battery

First, we will focus on our battery. Please take the battery labeled ego-S and twist the battery to the left to remove it from the saturn atomizer which comes attached to the top of your battery. Your battery will come partially charged, and it is important that you use it until there is no more charge before connecting it to your USB charger for the first time. Before connecting your battery to your charger, make sure the top connector portion of the battery above the button is completely dry and free of any eLiquid. Your battery and chargers will come with a 6 month manafacturer warranty that does not cover accidental damages or shortages that will occur if you neglect to clean your battery.

Turning Your Battery On

To turn your battery on, quickly click your button 5 times and the button light should flash. You can see the light will stay constant if you hold the button. Your battery will automatically stop working if this button is held down for 15 straight seconds. Turning your battery off simply requires 5 more quick clicks. Your light will flash again, and your battery is off.

Filling Your Saturn V2

Next, take the saturn atomizer, or heating element and remove the small colored cap from the top of the device. You are able to twist off the cap to the left, and after the cap is competely dethreaded, you will be able to pull the rest out. Do not lose the small silicone o-ring under the lip of your cap, or mouthpiece. Looking at your saturn, you will see that the top line on the plastic reads 1.6mls. Also notice two wicks on opposite ends inside your saturn. To fill the saturn tank atomizer, you will want your eLiquid to reach this 1.6ml line and saturate the wicks on the side. Looking through the top of the saturn, you will notice a small metal hole in the middle of the atomizer; it is important not to flood this as you fill your atomizer with eLiquid. To fill your saturn correctly, tilt it a 45 degree angle and slowly drool eLiquid through the insides of the saturn. Once your eLiquid fills to the 1.6ml line, saturates the wicks on the side to where they appear clear and full of liquid, and has avoided the metal hole, your saturn is ready to be connected to the battery and be primed.

To connect your battery to your saturn, simply thread the top of the battery into the bottom of the saturn to the right. It is important not to overtighten the battery, but also not to keep it loose and wobbly on top.  

Priming Your Saturn V2

To prime a newly filled saturn V2 tank atomizer, you can either let it sit freshly filled with liquid for approximately 5 to 10 minutes, or you can take about 5 to 10 puffs. If you opt to take inital puffs to prime your saturn, inhale through the moutpiece while simultaneously pressing the button on the battery. Release the button and exhale when ready. The first few puffs will not be full of vapor or flavor and might even taste a bit burnt. Do not worry. After about 5-10 drags you should experience a medium to harsh throat hit, a wonderful flavor, and full vapor production.

Cleaning And Charging Your Battery 

When your battery is dead, clean the top inside portion of the battery as mentioned, and twist onto your USB charger. Twist to the right until the light on your battery flashes. Do not overtighten your battery after there is a connection. The light on your USB will stay red for about 1 1/2 to 2 hours until your battery is fully charged and the light on your USB charger turns green. Take the battery off of the charger when the light turns green. We do not recommend charging your battery overnight. You should get about 6-8 hours of usage out of your battery.



EGO C STARTER KIT TUTORIAL

Assembling Your Heating System

Your battery is the bottom piece labeled Ego-C with the button placed near the top of the battery. This battery will come threaded to your base, cone, and tank. The two tanks that arrive attached to your cone and base are for shipping purposes only and may be discarded. 5 refillable tanks should come inside of the kit next to your atomizers. To remove your battery, hold the cone and base firmly together between the silver portion of the base and the colored portion of the cone, and unthread your battery by twisting it to the left. Place your battery aside, and remove the base from the cone by twisting the silver base to the left from the bottom of the colored cone. Next, remove the shipping tank from the top of your cone and discard this. Now that we have our base disattached, place a new atomizer into the top of the base. It will fit right on top without requiring you to twist it in. Please place the cone on top of your base and atomizer and thread it on. Place three drops of eLiquid directly onto the top of the wick (pointed portion) of your atomizer. This is a method called "priming" and should be done only once with every NEW atomizer. Next, take a plastic tank and remove the silicone cap from the bottom of the tank. Take your eLiquid and fill your tank into the bottom hole approximately 2/3 full, leaving room for air and the silicone cap to be placed back on. Place your silicone cap back on making sure all edges are flush with your tank. Please take your tank and push it into your cone and primed atomizer and twist it a quarter turn after you hear a small pop (your pointed wick will pierce the bottom of the silicone cap). Pull your tank from the base about a fingernail's width to allow airflow and create an easier draw of vapor.
 

Cleaning, Charging, And Using Your Battery

Putting our focus back onto your battery, it is important to drain your batteries completely before charging the first time you use them. They will come partially charged. To charge your battery. make sure the top connector (metal portion near the button) is very clean and free of any eLiquid before making a connection to your USB charger. Neglecting to clean your battery may cause damage to your battery. USB charger, or wall adapter and is not covered in your battery's six month manufacturer warranty. Twist your battery onto your USB charger until the button on your battery flashes and notifies you of a connection. You may twist your battery a bit further to ensure a firm connection, but please do not over tighten you battery, as this may result in dethreading of your battery. When you have a connection, the light on your USB charger will be red, and turn green after approximately 1 1/2 to 2 hours when your battery has been fully charged. Please remove your battery from the USB charger as soon as the light turns green; overnight charging is not recommended. Your battery will last approximately 6-8 hours of usage. To turn your battery on, quickly click the button 5 times and the light should flash momentarily. When your battery is on, the light should stay constant on your button as long as it is pressed. Your battery will automatically stop after 15 seconds of holding down the button. To turn your battery off, simply quickly click the button 5 more times.

Attaching And Using Your Ego-C

Now, we will attach our battery to our heating system by twisting the battery to the right onto the bottom of the base. Please turn your battery on and inhale through the mouthpiece, or tank, while simultaneously holding down your button. You should experience an airy draw, flavor, and a light sensation on your throat. We hope this tutorial was helpful in setting up and using your Ego-C starter kit.

    There are no products in this category.

VAPURE NEWSLETTER